LP-PRO electric drive for 3 x 400V with power monitoring, display and emergency stop, incl. BF1 motor with bracket. Excl. cable.
Accessories can be selected via the menus below.
Accessories can be selected via the menus below.
LP-PRO electric drive for 3 x 400V with power monitoring, display and emergency stop, incl. BK1 motor with bracket. Excl. cable.
Accessories can be selected via the menus below.
Accessories can be selected via the menus below.
LP-PRO electric drive for 3 x 230V with power monitoring, display and emergency stop, incl. BF7 motor with bracket. Excl. cable. Accessories can be selected via the menus below.
LP-PRO electric drive for 3 x 230V with power monitoring, display and emergency stop, incl. BF1 motor with bracket. Excl. cable.
Accessories can be selected via the menus below.
Accessories can be selected via the menus below.
LP-PRO electric drive for 3 x 230V with power monitoring, display and emergency stop, incl. BK1 motor with bracket. Excl. cable.
Accessories can be selected via the menus below.
Accessories can be selected via the menus below.
Foil for control cover V7E
CPU processor print vers. 234 for LP-PRO
When the print has been replaced, a factory reset must be made.
The printed circuit board MUST be changed without voltage on the control!
When the print has been replaced, a factory reset must be made.
The printed circuit board MUST be changed without voltage on the control!
Stainless wire and end terminal
Defus photocell with adjustable sense distance 0-5m.
Jumper red, 2,54mm, H = 14 mm
For LP-PRO
For LP-PRO
Crawford bottom roller carrier, left
Crawford bottom roller carrier, right
Crawford handle / base plate, For 542 incl. Logo
Crawford middle hinge, For 542, 75x70mm
Crawford operator CDM9 complete, incl. Control 950A.
Original.
Original.
Crawford roller bracket for side hinge, 11mm, short
Crawford roller, short, 2", 11mm, L = 115mm
Crawford side hinge 342/542, incl. Bracket
The print can be used for both digital and mechanical end stops.
Has a built-in 434 MHz radio receiver.
Has a built-in receiver for wireless edge protection, door contact (requires WSD module).
Up-Stop-Down buttons in lid.
Parameter adjustment with digital display.
2 programmable potential-free relay outputs - e.g. for traffic lights.
Automatic selection of edge protection (optical, 8k2 electrical sensor strip or DW contact 1k2 with test)
Auto close, half open, ventilation open.
Possibility of automatic wire slack compensation or self-adjustment of the closing position when changing the floor height.
Input terminals for pull switch, photocells, edge protection, etc.
Control for more advanced solution than TS970.
Has a built-in 434 MHz radio receiver.
Has a built-in receiver for wireless edge protection, door contact (requires WSD module).
Up-Stop-Down buttons in lid.
Parameter adjustment with digital display.
2 programmable potential-free relay outputs - e.g. for traffic lights.
Automatic selection of edge protection (optical, 8k2 electrical sensor strip or DW contact 1k2 with test)
Auto close, half open, ventilation open.
Possibility of automatic wire slack compensation or self-adjustment of the closing position when changing the floor height.
Input terminals for pull switch, photocells, edge protection, etc.
Control for more advanced solution than TS970.
Pro Loop 2 detector for 1 loop with 2 relay outputs.
Mounting on standard DIN Rail.
Mounting on standard DIN Rail.
Pro Loop 2 detector for 2 loops with 2 relay outputs.
Mounting on standard DIN Rail.
Mounting on standard DIN Rail.
Complete ready-made ground loop for loop detector.
Ready to install.
Ready to install.
Til frekvensomformer .
SPRING SHAFT COUPLING L = 100mm
Mounting flange for ITS radar
Cable for ITS radar 12 pol. 10m long
Emergency operation drive for gemobkxn motor
Consists of DW hose, 2 x hose connector, cable clamps, screws, pop rivets and cable ties
PVC profile for low threshold door, mounted on rail in dooropening