Flashing for rail, grey L = 2130 mm.

Flashing for rail, grey L = 2282 mm.

Flashing for rail, grey L = 2522 mm.

Roller slide in galvanized steel, suitable for side hinges of 70mm, and roller of 11mm

LP-PRO electric drive for 3 x 400V with power monitoring, display and emergency stop, incl. BF7 motor with bracket. Excl. cable.
Accessories can be selected via the menus below.

LP-PRO electric drive for 3 x 400V with power monitoring, display and emergency stop, incl. BF1 motor with bracket. Excl. cable.
Accessories can be selected via the menus below.

LP-PRO electric drive for 3 x 400V with power monitoring, display and emergency stop, incl. BK1 motor with bracket. Excl. cable.
Accessories can be selected via the menus below.

LP-PRO electric drive for 3 x 230V with power monitoring, display and emergency stop, incl. BF7 motor with bracket. Excl. cable. Accessories can be selected via the menus below.

LP-PRO electric drive for 3 x 230V with power monitoring, display and emergency stop, incl. BF1 motor with bracket. Excl. cable.
Accessories can be selected via the menus below.

LP-PRO electric drive for 3 x 230V with power monitoring, display and emergency stop, incl. BK1 motor with bracket. Excl. cable.
Accessories can be selected via the menus below.

M20  coupling, E-KVE-M20

Foil for control cover V7E

CPU processor print vers. 234 for LP-PRO
When the print has been replaced, a factory reset must be made.
The printed circuit board MUST be changed without voltage on the control!

Stainless wire and end terminal

Hjørneinddækning garageport med 15gr. 1stk H + 1stk V. Tilpasset 15graders taghældning.

Hjørneinddækning garageport med 25gr. 1stk H + 1stk V. Tilpasset 25graders taghældning.

Defus photocell with adjustable sense distance 0-5m.
Opening angle ± 5°. Beam angle ± 1.5°. Adjustable time for the output relay (0-10sec).
Output relay N.C./N.O. Load 240 VAC/2A. Dimensions: 17x50x50mm. IP67.
With mounting bracket so sensor can be angled.
Power consumption >70mA. Light immunity 25,000 Lux. LED for Power, Output and Signal.
Used e.g. to detect if something is at a sensible distance (car sensor at ramps etc.)

Jumper red, 2,54mm, H = 14 mm
For LP-PRO

Crawford bottom roller carrier, left

Crawford bottom roller carrier, right

Crawford handle / base plate, For 542 incl. Logo

Crawford middle hinge, For 542, 75x70mm

Crawford operator CDM9 complete, incl. Control 950A.
Original.

Crawford roller bracket for side hinge, 11mm, short

Crawford roller, short, 2", 11mm, L = 115mm

Crawford side hinge 342/542, incl. Bracket

The print can be used for both digital and mechanical end stops.
Has a built-in 434 MHz radio receiver.
Has a built-in receiver for wireless edge protection, door contact (requires WSD module).
IP54 - with CEE connector / IP65 with supply voltage directly connected.
Up-Stop-Down buttons in lid.
Parameter adjustment with digital display.
2 programmable potential-free relay outputs - e.g. for traffic lights.
Automatic selection of edge protection (optical, 8k2 electrical sensor strip or DW contact 1k2 with test)
Auto close, half open, ventilation open.
Possibility of automatic wire slack compensation or self-adjustment of the closing position when changing the floor height.
Input terminals for pull switch, photocells, edge protection, etc.
Control for more advanced solution than TS970.

Nice UDL2 control for Loading leveler with hinged lip.
In black box, type NG (IP65) with 2 buttons (up and return).
Box dimensions: 210 x 310 x 125 mm (WxHxD).
Control board is standard UDL2 (for hinged and sliding lip levelers). Voltage supply 3x400V AC, N, PE / 3x400V AC, PE / 3x230V AC, PE / 1x230V AC, PE. Max valve load: 24 VDC/0.83 Amp.Hydraulic pump max: 1.2KW

Marantec RS300K control for Loading leveler with hinged lip.
In white box (IP65) with 2 buttons (up and return).
Box dimensions: 215 x 275 x 190 mm (WxHxD). Control board is standard RS300K but with special Loading software.
Power supply 3x400V AC, N, PE / 3x230V AC, PE. Internal power supply 24 VDC / 2.2Amp. Max valve load: 24 VDC/0.6 Amp. Hydraulic pump max: 2.2KW / 8A.

Nice UDL2 control for Loading leveler with telescopic lip.
In black box, type NG (IP65) with 4 buttons (up, out, in and return).
Box dimensions: 210 x 310 x 125 mm (WxHxD).
Control board is standard UDL2 (for hinged and sliding lip levelers). Voltage supply 3x400V AC, N, PE / 3x400V AC, PE / 3x230V AC, PE / 1x230V AC, PE. Max valve load: 24 VDC/0.83 Amp.Hydraulic pump max: 1.2KW