Lid complete with push button and emergency stop
Emergency stop, diameter 22 mm, complete. Emergency stop has been changed to Ø22 early 2004. Ø16 can be replaced by drilling up the hole in the lid.
Emergency stop, diameter 16 mm, complete
.jpg?v=109428944)
EHLDB basic PCB (type EHB), 3x230 Volt.
EHB Basic PCB frequence control FO. 1 x 230 V. (Fits FO1/FO2)
For motor without brake. Print with end stop for Becker gear motor with hollow shaft in aluminum
For motor with brake. Print with end stop for Becker gear motor with hollow shaft in steel and click cover. Cannot be used for older type with screwable lid
3 non-energised outputs. Type UDM1. Door open signal, door closed and photo or error. Requires that 9-pole socket in control is available
For LS1 light control unit, 12 V /. Print for LS1 lamp control. 2 outputs, max load 12V / 20VA. DIP for selecting function
L = 4 m. Cable with plug at the motor end
.JPG?v=108877064)
L = 20 m. Cable with plug at the motor end
Type BK5, 110 Nm, 30 rpm. * Discontinued - sold as long as stocks last * A110ME/30LK with mechanical end stop. For Lindab EHLDB control
Lid for end stop housing for BECKER motor with release clutch. BF typs with srewable lid.
For gear with steel hollow shaft. Cover of cable connections. Lid to be screwed on. Has changed mid-2005
For gear with steel hollow shaft. Cover of cable connections. Lid to be screwed on. Has changed mid-2005
For door with 1" shaft.
Consists of DW hose, 2 x hose connector, 2 x lock ring for 1" shaft, cable clamps, screws, pop rivets and cable ties
Consists of DW hose, 2 x hose connector, 2 x lock ring for 1" shaft, cable clamps, screws, pop rivets and cable ties
.JPG?v=108878356)
For door with 5/4" shaft.
Consists of DW hose, 2 x hose connector, 2 x lock ring for 5/4" shaft, cable clamps, screws, pop rivets and cable ties
Consists of DW hose, 2 x hose connector, 2 x lock ring for 5/4" shaft, cable clamps, screws, pop rivets and cable ties
Electrically heated pad for motor 230V/40 watt, with 7 meter cable and thermostat. LS:93-K-A-620-04
Electrically heated pad for motor 400V/40 watt, with 7 meter cable and thermostat. LS: 96-K-A-620-04
For Lindab car wash control unit. Fits both EHLDB and EHLDC carwash controls
NOTE - The lock does not fit on 3 "rails and low lift rails .
For basic PCB with 8 DIP switches.
Programme EPROM with the latest version.
Programme EPROM with the latest version.
With 2 m, cable. Electric box with the possibility of connecting different equipment to the two additional end stops found in the Becker gear motor
Handle for adjustment of clutch. For BECKER BF3 motor with release clutch.
For Becker motor, GEMOBECK40.
For Becker motor, GEMOBECK40.
Support with snap for photocell. LP drawing no. 010.02.106-04
Chain house for BECKER with emergency chain. Excl. Chain.
For emergency chain drive. Also used for replacement air controls type BA2 in combination with Lindab EHLDB and EHLDC controls
Communication cable for lamp control with socket and plug.
For LS1 light control unit.
For LS1 light control unit.
Type EO1, Ø8 mm, 150 mm cabel. Type EO1, ø 8mm, 150mm cord. Used to switch on / off auto-close
Lid for control box for light control EHB
For LS1 light control.
For LS1 light control.