L = 4 m. Cable with plug at the motor end
Handle for adjustment of clutch. For BECKER BF3 motor with release clutch.
For Becker motor, GEMOBECK40.
For Becker motor, GEMOBECK40.
Type BF5, 150 Nm, 15 rpm. * Discontinued - sold as long as stocks last * A150ME/15AK with mechanical end stop. For Lindab EHLDB control
.jpg?v=108876792)
Type BK2, 70 Nm, 16 rpm. * Discontinued - sold as long as stocks last * A70ME/16LK with mechanical end stop. For Lindab EHLDB control
Type BK5, 110 Nm, 30 rpm. * Discontinued - sold as long as stocks last * A110ME/30LK with mechanical end stop. For Lindab EHLDB control
.jpg?v=108876788)
Type BF8, 110 Nm, 30 rpm. * Discontinued - sold as long as stocks last * A110ME / 30AK with mechanical end stop. Only for Lindab EHLDB frequency control
Type BK4, 150 Nm, 15 rpm. * Discontinued - sold as long as stocks last * A150ME/15AK with mechanical end stop. For Lindab EHLDB control
Type BF7, 100 Nm, 25 rpm. * Discontinued - sold as long as stocks last * A100ME/25AK with mechanical end stop. For Lindab EHLDB control
Type BK1A, 100 Nm, 25 rpm. * Discontinued - sold as long as stocks last * A100ME/25LK with mechanical end stop. For Lindab EHLDB control
With 2 m, cable. Electric box with the possibility of connecting different equipment to the two additional end stops found in the Becker gear motor
Only foil without lid.
L = 10 m. Cable with connectors on both ends
L = 7 m. Cable with connectors on both ends
Type BF7S, 100 Nm, 25 rpm. With built-in encoder. For EHS30 control
Type BK1S, 100 Nm, 25 rpm. With built-in encoder. For EHS30 control
For 1" shaft, 3 x 400 V. Electric operation includes motor bracket, wall bracket for chain, wiring angles and Fraba DW with spiral cable
For 1" shaft, 3 x 400 V. Electric operation includes Fraba DW with spiral cable
.JPG?v=108878356)
For door with 5/4" shaft.
Consists of DW hose, 2 x hose connector, 2 x lock ring for 5/4" shaft, cable clamps, screws, pop rivets and cable ties
Consists of DW hose, 2 x hose connector, 2 x lock ring for 5/4" shaft, cable clamps, screws, pop rivets and cable ties
For door with 1" shaft.
Consists of DW hose, 2 x hose connector, 2 x lock ring for 1" shaft, cable clamps, screws, pop rivets and cable ties
Consists of DW hose, 2 x hose connector, 2 x lock ring for 1" shaft, cable clamps, screws, pop rivets and cable ties
For LS1 light control unit, 12 V /. Print for LS1 lamp control. 2 outputs, max load 12V / 20VA. DIP for selecting function
Fitted in control unit cover. Communication print between lamp control and EHLDC
3 non-energised outputs. Type UDM1. Door open signal, door closed and photo or error. Requires that 9-pole socket in control is available
Support with snap for photocell. LP drawing no. 010.02.106-04
10 x 30 mm, for installation of pos.
Magnetswitch for building passdoor with magnet.
NOTE - The lock does not fit on 3 "rails and low lift rails .
Communication cable for lamp control with socket and plug.
For LS1 light control unit.
For LS1 light control unit.
Type LS1, complete with two outlets. Lamp control for EHLDB and EHLDC control. Max load 12V / 20VA. DIP for selecting function. Including wall bracket and communication cable. For use with EHLDC, communication prints must be installed in the EHLDC control cover