Defus photocell with adjustable sense distance 0-5m.
Opening angle ± 5°. Beam angle ± 1.5°. Adjustable time for the output relay (0-10sec).
Output relay N.C./N.O. Load 240 VAC/2A. Dimensions: 17x50x50mm. IP67.
With mounting bracket so sensor can be angled.
Power consumption >70mA. Light immunity 25,000 Lux. LED for Power, Output and Signal.
Used e.g. to detect if something is at a sensible distance (car sensor at ramps etc.)

Pro Loop 2 detector for 1 loop with 2 relay outputs.
Mounting on standard DIN Rail.
Dimensions 22.5 x 94 x 90mm, Supply voltage 100-240 V AC ± 10% , 50 Hz, 12-23mA, Power consumption 2.9VA. Max loop lead 100m 20-40uH (Ø 1.5m2 twisted 20 times per m. Loop inductance 20-1000uH).

Pro Loop 2 detector for 2 loops with 2 relay outputs.
Mounting on standard DIN Rail.
Dimensions 22.5 x 94 x 90mm, Supply voltage 100-240 V AC ± 10% , 50 Hz, 12-23mA, Power consumption 2.9VA. Max loop lead 100m 20-40uH (Ø 1.5m2 twisted 20 times per m. Loop inductance 20-1000uH).

Complete ready-made ground loop for loop detector.
Ready to install.
Circumference 10m and 15 m supply line.
Do not place closer to reinforcement bars than 15 cm.

ITS-AX4 Special 79GHz radar.
This radar can detect both motion and presence (stationary) in the sensor area.
The radar is initialized with a mobile phone App (Android/Apple).
The sensor range is 0.1 - 6m in length and 0.5 -1.5m to the right and left of the radar.
The right and left sides are set individually.
The radar has 2 modes - either as Anti collection or as open signal.
The radar comes with a 1m supply cable. A 10m extension cable can be purchased.
All connections are made to the end of the supply cable (an electrical/mounting box is required).
Supply voltage 9-24 VDc.< 2.5Watt. IP65. 2 relay outputs (Max150mA @ 24V DC) - NO/NO and NC/NC. Dimensions 108x74x17mm/32.2mm incl. M16 connection plug.

Mounting flange for ITS radar

Cable for ITS radar 12 pol. 10m long

Foil incl. circuit board for Marantec CS310

Type BIRCHER.

10 pcs. Membrane contact with connection terminals, Bircher

DW40 system complete
Contains
1 spiral cable 5 x 0.5mm, 1,6m orange
1 pcs. DW40
1 pcs. membrane box
1 pcs. STDPOSEDW

Suitable for EHC"

IP55, 12/24 VAC/DC. Including DW40, mounting box, cable and resistor

Clear plastic tube for DW 2,0 x 4,0 MM

Clear plastic hose for DW40 membrane connector. 3,0 x 5,0 MM

L = 500 mm. 3,0 x 5,0 MM

Complete. With 2 x hose nozzle, hose, pop rivets and hangers

Brass. Brass hose nozzle for DW hose in bottom rubber

With 7 m cable. Hercules 2 radar can distinguish between vehicles and people. It has 2 outputs - set to No or NC. Adjustable filters for eg intersecting traffic, slow traffic, field size, etc. Can be adjusted according to the conditions at the installation site. Mounting height between 2 and 7 meters. Remote control RegloBeam 2 can be used. Supply voltage 12-28 VAC / 12-36 VDC, 75mA

Remote control for coding FALCON radar
Gives access to adjustment for radar.

Remote control for coding FALCON radar

Proloop 2, 24 VAC/DC. For 11-pole socket

Dalmatic type JD25-1. For 11-pole socket

Dalmatic type JD25-1. For 11-pole socket

For DOT 100. ø10 mm, 15 meter cable

For DOT 100. Ø10 mm, 15 meter cable

24230 V AC/DC, IP67. LB gate 25 with NO / NC contact kit
Built with amplifier  Too Nassau door

**FINAL** 1 pcs. Left -  85 x 76.5 x 38 mm For 11-pole socket for the photocell transmitter & receiver.
C2001, 220 VAC. Photocell amplifier, type Conquest C2001, relay output, dimensions: 85x76.5x38 mm, for 11-pole socket. Intended for transmitter / receiver photocells

C2001, 24 VAC. Photocell amplifier, type Conquest C2001, relay output, dimensions: 85x76.5x38 mm, for 11-pole socket. Intended for transmitter / receiver photocells

C2001 24 VAC/DC. Photocell amplifier, type Conquest C2001, relay output, dimensions: 85x76.5x38 mm, for 11-pole socket. Intended for transmitter / receiver photocells

Transmitter/receiver with relay out.