Foil for control cover V7E
CPU processor print vers. 234 for LP-PRO
When the print has been replaced, a factory reset must be made.
The printed circuit board MUST be changed without voltage on the control!
When the print has been replaced, a factory reset must be made.
The printed circuit board MUST be changed without voltage on the control!
Jumper red, 2,54mm, H = 14 mm
For LP-PRO
For LP-PRO
The print can be used for both digital and mechanical end stops.
Pro Loop 2 detector for 1 loop with 2 relay outputs.
Mounting on standard DIN Rail.
Mounting on standard DIN Rail.
Pro Loop 2 detector for 2 loops with 2 relay outputs.
Mounting on standard DIN Rail.
Mounting on standard DIN Rail.
Complete ready-made ground loop for loop detector.
Ready to install.
Ready to install.
Til frekvensomformer .
Mounting flange for ITS radar
Cable for ITS radar 12 pol. 10m long
Emergency operation drive for gemobkxn motor
Consists of DW hose, 2 x hose connector, cable clamps, screws, pop rivets and cable ties
.jpg?v=122314608)
D-PRO HSI 1X230 control, set for HSI.
Controller comes with emergency stop and has IP65 protection class
Supply voltage must be 1 x 230V.
(Note: Supply cable is permanently mounted on the inverter)
Controller comes with emergency stop and has IP65 protection class
Supply voltage must be 1 x 230V.
(Note: Supply cable is permanently mounted on the inverter)
5-pin green connector. Used for PRO-LINE control.
6-pin black connector. Used for PRO-LINE control.
1m spiral, 1.6m straight cable, orange, including z-brackets and connectors.
Spiral stretch 1:3.
Spiral stretch 1:3.
.jpg?v=122524286)
1,5m spiral, 5 m straight cable, orange, including z-brackets and connectors.
Spiral stretch 1:3.
25 pcs per colli
Spiral stretch 1:3.
25 pcs per colli
Foil incl. circuit board for Marantec CS310
Spiral cable 5 x 0,5mm, black. L = 300/800/1600
5 pcs per colli
5 pcs per colli
.jpg?v=122641083)
Spiral cable 5 x 0,5mm, black. L = 300/800/3000
5 pcs per colli
5 pcs per colli
_(2).jpg?v=122641086)
Spiral cable 5 x 0,5mm, black. L = 300/800/5000
5 pcs per colli
5 pcs per colli
Ferrite core for use in light grids or other electrical accessories, where electrical noise in an installation can be problematic.
GFA motor with release clutch. 90Nm, 24 RPM,
suitable for 1" shaft, and including key for hollow shaft. 3x230/400V IP65.
suitable for 1" shaft, and including key for hollow shaft. 3x230/400V IP65.
GFA chain release motor. 90Nm, 24 RPM, suitable for 1" shaft, and including key for hollow shaft.
3x230/400V IP65.
4 meter chains are included as standard.
3x230/400V IP65.
4 meter chains are included as standard.
GFA motor with release clutch. 90Nm, 30 RPM, suitable for 1" shaft, and including key for hollow shaft.
3x230/400V IP65.
3x230/400V IP65.
GFA motor with release clutch. 90Nm, 20 RPM, suitable for 1" shaft, and including key for hollow shaft.
3x230/400V IP65.
3x230/400V IP65.
GFA chain release motor. 90Nm, 20 RPM, suitable for 1" shaft, and including key for hollow shaft.
3x230/400V IP65.
4 meter chains are included as standard.
3x230/400V IP65.
4 meter chains are included as standard.
GFA chain release motor. 90Nm, 21 RPM, suitable for 5/4" shaft, and including key for hollow shaft.
3x230/400V IP65.
4 meter chains are included as standard.
3x230/400V IP65.
4 meter chains are included as standard.
GFA chain release motor with frequency converter. 80Nm, 60 RPM, suitable for 1" shaft, and including key for hollow shaft.
1x230V IP65.
1x230V IP65.
GFA chain release motor with frequency converter. 140Nm, 100 RPM, suitable for 1" shaft, and including key for hollow shaft.
3x230/400V HSI IP65.
4 meter chains are included as standard.
3x230/400V HSI IP65.
4 meter chains are included as standard.